P1 Series Ceramic Heater and Thermistor with Thermal Grease – 60W
Replacement ceramic heating with thermistor and thermal paste for 3D printers Bambu Lab P1 Series (P1P, P1S). This module is designed for users who need to reliably restore hotend heating after long-term use, mechanical damage, or thermal overload.
Note: the original Bambu Lab module for P1 Series has a rated power of approx. 48 W and is usually supplied in a pack of 3 with thermal paste and clips.(us.store.bambulab.com)
This product represents a single replacement module of a ceramic heating element with a thermistor and thermal paste with comparable parameters (manufacturers often state a rounded power of 60 W for 24 V variants)(hictop3dprinter.com) – ideal for service and quick replacement without the need to buy entire hotend assemblies.
Main benefits
- Compatibility with Bambu Lab P1 Series
Fully compatible with Bambu Lab P1P and P1S printers, designed exclusively for this series (cannot be used for X1 Series due to a different connector).(asia.store.bambulab.com)
- Integrated module – heater + thermistor
The ceramic heating element and thermistor are merged into one module with an integrated connector, which increases contact reliability in demanding conditions and simplifies replacement.(us.store.bambulab.com)
- Fast heating up to 300 °C
The heating element can heat the nozzle up to 300 °C, which allows printing of common and technical materials (PLA, PETG, TPU, ABS, ASA, PA etc.), depending on the limitations of your printer.(us.store.bambulab.com)
- Accurate temperature measurement
The integrated thermistor has high accuracy and measurement stability, so the firmware can precisely regulate the nozzle temperature and minimize fluctuations.
- Thermal paste included
The supplied thermal paste improves heat transfer between the ceramic body and the hotend block, increasing heating efficiency and temperature stability.(us.store.bambulab.com)
- Suitable for maintenance and preventive replacement
Ideal as a service part in stock – in case of a heater or temperature sensor error (runaway, open circuit, unstable temperature), you can quickly restore operation without a long wait for a spare part.
Typical use
- replacement of a damaged or burnt-out ceramic heating element of the hotend
- replacement for errors such as abnormal nozzle temperature, open circuit, or inability to reach target temperature
- preventive replacement after long operation or after a mechanical impact to the hotend
- service and maintenance of a fleet of Bambu Lab P1P / P1S printers in companies, workshops, schools, and makerspaces
Technical parameters
| Parameter | Value |
|---|
| Product type | Ceramic heating element with integrated thermistor |
| Designed for | Bambu Lab P1 Series (P1P, P1S) |
| Power supply | 24 V DC (typical for P1 Series)(hictop3dprinter.com) |
| Rated power | approx. 48–60 W (depending on the specific manufacturer; original Bambu Lab states 48 W)(us.store.bambulab.com) |
| Operating temperature | -10 °C to 300 °C(us.store.bambulab.com) |
| Temperature sensor | Integrated thermistor (type according to Bambu Lab printer specification) |
| Connector | Integrated combined connector (heater + thermistor in one) |
| Recommended use | Hotend spare part, service, maintenance |
| Packaging | 1× ceramic heater with thermistor, 1× thermal paste (amount per package for one assembly) |
Warning: always verify the printer model and connector type before ordering. The version for P1 Series *is not compatible** with the X1 series.(jp.store.bambulab.com)
Installation and recommendations
- Turn off the printer and disconnect the power supply.
- Let the hotend cool down completely.
- Remove the toolhead cover according to the Bambu Lab manual.
- Disconnect the original ceramic heater and thermistor module from the board in the toolhead.
- Remove the old heating element from the hotend block.
- Apply a thin uniform layer of thermal paste to the new element in contact with the block.
- Insert the new element into the hotend block and secure according to the instructions (screw / clip).
- Plug the new integrated connector into the appropriate port on the board in the toolhead.
- Check the wiring to ensure it is not under tension or in contact with moving parts.
- Perform a nozzle heating test and verify that the temperature rises smoothly and holds the set value.
For a detailed procedure, it is advisable to follow the official Bambu Lab Wiki instructions for replacing the Ceramic Heater & Thermistor – P1 Series.
Why keep a ceramic heater with thermistor in stock
- Minimal printer downtime – immediately replace the faulty part and continue printing.
- Cheaper than an entire hotend – saves service costs.
- Suitable for intensive operation in companies or farms, where printer failure means delay of orders.
Keywords (for customers looking for the product)
3D printing Bambu Lab P1P, Bambu P1S spare parts, ceramic heating element P1 Series, thermistor hotend Bambu, heater block P1P, replacement nozzle heating 300 °C, 24 V heater Bambu Lab.
Key features:
- Original construction type for Bambu Lab P1 Series – compatibility with P1P and P1S
- Integrated module of ceramic heating element and thermistor in one connector
- Fast and stable nozzle heating up to 300 °C for a wide range of filaments
- High temperature measurement accuracy thanks to high-quality thermistor
- Includes thermal paste for optimal heat transfer to the hotend block
- Ideal as a quick replacement for heater or thermistor errors without replacing the entire hotend
- Suitable for service, maintenance, and minimization of downtime for Bambu Lab P1 Series printers
